This article which follows involving Tools You Need to Install a New Bathtub is highly enjoyable. Have a go and draw your own findings.
Mounting a bath tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is also a reasonably tough job. If the old tub is conveniently obtainable, the project can relocate quickly; if you need to open up a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and also fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This short article will assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new bathtub and also do not require to transform the plan of your previous water system pipelines.
Your devices and also material checklist ought to consist of the following:
Getting ready for the Setup
First of all, the supporting structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the limited gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before moving on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the tub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost flexible faucet connector to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water supply as well as examine all joints and brand-new pipework for leakages and also tighten them if required. Fill the tub as well as also inspect the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the tub must wait until the bathtub has actually been used at the very least once as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location in between the tap as well as the sink. Safeguard the tap in place with the producer provided backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap ports. The previous type should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealer can crack fairly very early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking time to read through our article post. Please set aside a second to promote this blog if you liked it. I thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Quote